PCMtuner-tool

 Q: Anybody did successfully BMW mevd 17.2.9 in obd or bench mode using foxflash ? A: Yes, foxflash read and write on bench. Fox flash pinout to BOSCH MEVD17.2.9 [ 1797 ] — BMW [Gasoline] To read and write use the following driver: → BENCH TRICORE → BMW → TC1797 — BMW → MEVD17.2.9

  Problem: I got a problem running foxflash software , error "The DLL LIBCURL.DLL cannot be loaded" (shown image below). Any suggestion? Solution: Operating system issue. Change a clean system. Better be Win10 64bit. 1 Shutdown date and time automatically syncs 2: shutdown defender 3: shutdown antivirus system 4: run foxflash manager click active button 5 : keep manger run 6: run foxflash

  Question: Renault Espace 2010 SID305 Any pinout, Bench or OBD? PCMtuner site does not show pinout, window is white. Is possible read and write Sid305 in Bench? Answer: SID305 is done via OBD (module 25), so no pinout. Module 25 Renault/Nissan 1.5dCi is OBD. PCMTuner SID305 Success reports: 1). Nissan juke 1.5dci Sid305 Dtc off 2). Nissan Qashqai 1.5DCI SID305/306 OBD Read and Write — OK 3). Renault scenic3 1.5dci Read and write with pcm tuner , sid305 Dpf off 4). Renault Scenic 1.5DCI 2009 — SID305 OBD Read/Write — No problem 5). read and write via obd Renault scenic3 sid305 with no problems 6). SID305 1.5Dci OBD R/W sounds good 7). Renault Scenic 3, sid305 1,5 MB read/write OBD 8) Sid305 Obd read and write, nissan Qashqai 1.5dci 9) Renault scenic 1,5dci 2012 95cv SID305 Module 25 reading/writing stage 1 → OBD Checksum ok http://www.pcmtuner.org/pcmtuner-read-and-write-renault-scenic-sid305-by-obd/

  Foxflash programmer can read and write Ford/Fiat/Peugeot/Citroen DCU102 Visteon ecu in boot mode. You must copy flash in ST10 boot mode and eeprom. Kit to use: – Multifunction cable – 2 resistance of 1000 Ω Connect multifunction cable and the resistances as shown To read and write use the following driver: → TOOLS BOOT MODE → ST ST10Fxxx → ST10F273 / ST10F275 / ST10F276 *K or → ST10F273 / ST10F275 / ST10F276 *CAN Alternatively, read via RX TX: Kit to use: – — Multifunction cable – — 2 resistance of 1000 Ω  — Transistor PNP 2N3906 Connect multifunction cable and the resitances as shown. To read and write use the following driver: → TOOLS BOOT MODE → ST ST10Fxxx → ST10F273 / ST10F275 / ST10F276 *RxTx www.iecutool.com

 User contribution: How to build an OBD2 to 9pin adapter for reading John Deere,NEW HOLLAND etc using foxflash/kt200? You can make this how to make an adaptor from DFOX tool to Dimsport cables. this also works with all the Foxflash -KT200 etc and Alientech cables. and buy a JD cable for Dimsport New Genius.

 Both pcmtuner and foxflash will read and write EDC17CV41 ECU on bench. PCMTuner EDC17CV41 Pinout Edc17cv41 Read/Write, checksum ok. Need to check whether you have version 1 or 2 as gpt pins go on different pins / point. worked on pins GPT 66 68. used module 71. Foxflash EDC17CV41 Pinout Connect the multi-function cable as follows. For this ECU there are 2 different types of hardware versions, try the following 2 combinations in series. The ECU will not suffer any damage during connection tests. Some ECUs enter bench mode with the pinout below To read and write use the following driver: → BENCH MODE → [brand] → TC1797 — [brand] → EDC17 CV41

 Today a EDC16C34 arrived in the famous Peugeot 5008. Foxflash is capable to read and write it flawlesly with no problems at all. Keep voltage as 13.4V. In case software hangs up — you can kill it wit the other EXIT button. Pinout is standard only K bus wire www.iecutool.com