PCMtuner-tool

  Problem: Foxflash read MSV70 E60 523i via OBD, wrote mod, but failed. tried to write ori again, gets stuck at 93% anyone had this issue? Solution: Voltage looks low, write at least 13.8v. If still failed to write mod file, only if Mod file bad, you will need to Write original file in BDM. Foxflash Pinout to Siemens MSV70 Solder the dip/sip connectors on the pcb and do a link: To read and write use the following driver: → BDM/ JTAG MODE → BDM MPC → MPC55x/56x ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

 Possible to read eeprom/flash data of Mercedes Benz CRD3.40 ECU with pcmtuner ? Yes, via module 52 BSL mode. pcmtuner pinout for delphi crd3.4 in bsl Direct Connection BOOT & CNF1 CONNECTION Connect the BLUE and GREY wires of the cable F32GN037C as shown here below: WARNING If instead of the 14-pin component, used for CNF1 signal, it is present a 8 pins component, the CNF1 connection must NOT be carried out, it is necessary the BOOT connections ONLY. Check: pcmtuner module 53 BSL instruction Flex and Foxflash can do it on bench but if written wrong file and do it in boot. If you cannot do in BSL then not possible to recover eeprom/flash. ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

 Jaguar XE 2.0d 2017 MEDC17.9 read and write successfully by foxflash ecu programmer, checksum by foxflash. DPF OFF , EGR OFF , ADBLUE OFF. Foxflash pinout to BOSCH MEDC17.9 [ 1793 ] — Jaguar Connect the multifunction cable as follows: Attention: Some MEDC17.9 enter in Bench mode with another CAN line. If with the previous pinout doesn't go in bench tricore mode, then try again by connecting it as follows: To read and write use the following driver: → BENCH TRICORE → JAGUAR → TC1793 — JAGUAR → MEDC17.9 Read ok Write ok, checksum by tool ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

 Can I read Fiat MARELLI IAW 7GF ECU with foxflash ecu tool ? Yes, foxflash will read and wite IAW 7GF via jtag. FoxFlash Pinout to Fiat Marelli IAW 7GF MPC5554 Connect the multifunction cable as follows: Solder the rainbow flat cable on the pcb: To read and write use the following driver: -BDM/Jtag -BDM/Jtag Mode -Jtag NEXUS MPC/SPC -MPC 55XX ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

  Pcmtuner new test feedback: Peugeot Patner 2015 1.6 hdi Sid807evo read and write bsl module 53, dpf egr off Ok. Check: Pinout for PSA SID807EVO Pcmtuner module 53 BSL instruction Psa Sid807EVO read, checksum and write OK Image attached: ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

  Problem: I have tried to clone MEDC17.9 ecu and foxflash won't let me write micro flash because otp protected. Foxflash said that medc17 cloning free service. Any advice please? Cloning tool in Foxflash is for VAG Group ECU's. Check: Foxflash Tricore Clone MEDC17 ECUs Procedure ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html

 Foxflash read and write Mercedes Benz Sprinter CRD3.20 on bench successfully. Foxflash pinout to CRD3.20 TC1797 To read and write use the following driver: → BENCH MODE → MERCEDES BENZ → TC1797 — MERCEDES and choose: → CRD3.2x ECU tool recommendation: PCMtuner https://www.iecutool.com/wholesale/pcmtuner-ecu-programmer-tool.html