PCMtuner-tool

 Is it safe read write flash file from this Denso ecu (4N13) using pcmtuner via OBD? Car- 2012 Citroen C4 aircross, 1.8 d, 110 kw. I have tried to read with module 26 (identify and read ok, but afraid to write). Yes, go for it. pcmtuner read and write Denso 4N13 via OBD. It will read, write and do checksum. If failed, try do it on bench.

 Question: How to read (without opening) a Bosch ECU (0261S11653 / 8639595–01 / 170500554 DME) of a BMW 320i (F30) vehicle with foxflash ? I have tried the connection in several ways… but so far without success. Solution: It is a MEVD17.2.9 ECU. Foxflash pinout to MEVD17.2.9 RED: + 12V 1, 22, 40 BLACK: GROUND 2 BLUE: CAN-H 43 ORANGE: CAN-L 44 WHITE 16 BROWN 43 To read and write use the following driver: → BENCH TRICORE → BMW → TC1797 — BMW → MEVD17.2.9 Feedback: I was able to successfully read the DME. Note on the cable there are two white wires, (one pure white and the other with a red stripe), the correct one is pure white.

 How to read and write by FoxFlash through Bench mode Honda Civic MK10 2018 MED17.9.3 ??? Honda edc17 med17 have been done bench and boot. There are 2 options in FoxFlash, bench read and write through and another option bench and boot through pinout. Foxflash Honda MED17.9.3 bench pinout BOSCH MED17.9.3 [ TC1793 INT.F.] — Honda Kit to use:  — Multifunction cable – 1 resistance of 1000 Ω – 3 resistances of 1000 Ω (for boot method 2) To read and write use the following driver: → BENCH TRICORE → HONDA → TC1793 — HONDA → MED17.9.3 Foxflash Honda MED17.9.3 boot pinout Step 1: Password Search Connect the pinout below with multifunction cable. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Tool Password → PASSWORD BFT → Click on "Find Password" and follow the software messages. Now that the password has been found it's possible to read and write the control unit. See next step. Step 2: Read and Write ECU Connect with the multifunction cable the fol

  Problem: When i tried my first laptop to ID Honda Accord ECU as soon it did ID. After they i get USB not recognized error. Then i installed pcmtuner flash software in another laptop. Got every thing activated. Did ID honda eca via OBD. It did identified but again same error computer say USB not recognized. Tried uninstalling and installing UsB drivers still same. Plz check photos for reference Can you help? Solution: Do not plug 12v power into pcmtuner. Also, this work better with tactrix or openport interface. Don't forget to select it in the drop down box in pcm software. Feedback: All done using OpenPort 2.0 with pcmtuner software.

  Foxflash programmer will read and write Mercedes Benz gasoline SIEMENS VDO MSM2.0 ECU on bench. Here is the fox flash pinout to MSM 2.0. Select driver Mercedes Siemens ECUS 1.4/1.6 Siemends VDO MSM 2.0 FULL SYSTEM If old and new ecu have read flash and eeprom without problem. Write not work with foxflash. Have error. Cannot write any file as shown image below: After read flash/eprom — Disconnect ecu and restart software (unplug foxflash ) — restart Then connect again, Write flash, Also try lower power only need 13v on this ecu.

 Foxflash recent update adds FCA Dodge CONTINENTAL GPEC3 ECU. Here is the foxflash pinout to CONTINENTAL GPEC3 BAM SPC5674 CONTINENTAL GPEC3 FCA Pinout Connect with the multifunction cable the CNF1 on the pcb. READ AND WRITE ECU Use the driver: → TOOLS BOOT MODE → MOTOROLA FREESCALE BAM → CONTINENTAL GPEC3

 Which tool to read this computer BMW MSV70 DME? Foxflash : Yes, via BDM Jtag Connect multifunction cable as follows: Solder the dip/sip connectors on the pcb and do a link: Insert Siemens/Marelli adapter as in photo: To read and write use the following driver: → BDM/ JTAG MODE → BDM MPC → MPC55x/56x Ktag / Kess V2 : Need luck. The best option is BDM. Sometimes Kess v2 and ktag clone read ok but failed during writing, checksum error. Ori Kess done well OBD but takes long. Easy to remove and run in bdm. CG FC200: FC200 programmer does not support this computer.