PCMtuner-tool

  Problem: After write in ecu with foxflash tool ecu is bricked, ecu is EDC17CV42 Man Tgs 2014. Have full beckup and no work write File with backup, problem password. Ecu work read File and No work write. Any advice? Solution: You need to find password. Search password in flash file (tool boot password) and then you can write. Try to search in obd file but normally it will do in bench, but you can try with obd file. Since time better to make backup in bench before try to obd. Once you already extracted the password, read write normally.

 Can Foxflash read and write Ford Ranger SID209? Yes, first read obd password after that remove ecu and read/write boot mode. Reading was 2 mins, writing is 15–17 mins. SIEMENS CONTINENTAL SID209 [ TC1797 INT.F.] — Ford Boot Pinout to Foxflash Step 1: Password Search Connect the pinout and use the following driver: Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Tool Password → OBD PASSWORD SID209 FORD → Click on "Find Password" and follow the software messages. Attention: If you cannot find the password from Pinuot, you must launch the driver in OBD on the vehicle. Now that the password has been found it's possible to read and write the control unit. See next step. Step 2: Read and Write ECU Connect with the multifunction cable the following pinout and the boot shown below Use the foxflash driver : → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1797 www.iecutool.com

  Problem: Usage problem, the pc (Win11 system) has a lot of RAM and an empty hard drive and yet I have this error when reading EDC16C34 with foxflash . Error "Your computer's memory is insufficient" Solution: The error usually caused by insufficient computer memory. If your computer has enough RAM, try to delete foxflash software and install again. Feedback: Problem solved, remove foxflash then reinstall software. It works now.

 Godiag GT107+ is the upgrade version of GT107 . You don't need to connect extra GT105 breakout box to read gearbox TCUs. Here is an example of reading VAG DQ200 gearbox using gt107+. Device used: Pcmtuner programmer or kess v2 (pcmtuner is faster than kess v2 to read DSG gearbox) Godiag GT107+ DSG gearbox adapter Procedure: Connect pcmtuner with USB and main cable Connect pcmtuner with gt107+ gearbox adapter Connect jumper cable with DQ200 gearbox module follow the pinout Turn on ignition on the gt107+ Run pcmtuner flash software Select module 58 and read DQ200 data. It writes without problem as well. www.iecutool.com Read also: http://www.pcmtuner.org/pcmtuner-module-58-vag-dsg-cvt-instruction/

 Audi A5 2.0 177bhp ECU EDC17C46. Read and write fine with pcmtuner dongle on bench. Module 71. ECU info. Bosch EDC17C46–2.22 0281018128 VAG using sm2 pro with pcmtuner dongle and bench power supply. NOTE: If pcmtuner failed to read this ecu, after transistors replacement, it works perfectly.

  Problem: I tried to read Audi Simos 12 ECU with foxflash via obd, but failed. fox says virtual file not present in database. Solution: foxflash cannot read simos 12 via obd if there is no file in server. Foxflash engineer will upload vr file to server once it is available. You can read and write in boot mode. SIEMENS SIMOS 12 [ TC1797 INT.F.] — VW, Audi, Seat, Skoda Boot Mode pinout to foxflash ecu tool . Step 1: Password search: Connect with the multifunction cable the following pinout and the connections on the pcb. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Password → PASSWORD SIMOS 12 BENCH BOX → Click on "Find Password" Now that the password has been found it's possible to read and write the control unit. See next step. Step 2: Read and write ECU Connect with the multifunction cable the pinout. (Attention: Now remove the bench box ) Do the connection shown below. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1797

  Problem: I just installed the pcmtuner application I already have connected the equipment and the USB dongle but nothing responds in the application. Two errors: "User not activated" "USB Dongle Device Not Found" Solution: 1. Must send email and device serial number to tuner-box.com to activate it. 2. Install the dongle driver.