PCMtuner-tool

  Problem: Will foxflash programmer read and write edc17cv45 or not? I don't see anywhere in software have Kubota edc17cv45, where it's ? Solution: foxflash software does not have Kubota edc17cv45 driver on the list. But there is a BOSCH EDC17 CV54 [1767 ]– Agco [Diesel] driver. If the processor CPU is the same as TC1767 there is a chance to read/write it on bench. To read and write EDC17CV45 [1767] use the following driver: → BENCH TRICORE → AGCO → TC1767 – AGCO → EDC17 CV54 Pinout is the same for KUBOTA EDC17cv45 tc1767 If CPU processor is not TC1767, then fox flash will not read and write this ecu. You may need other programmers, dimsport etc. Here is the bench pinout to Bosch EDC17CV45 TC1872 Kubota to dimsport.

 Good news! Foxflash ecu programmer released new update- adding FCA group GPEC2 GPEC3 GPEC4LM GPEC2A ECUs. Continental GPEC2 GPEC3 GPEC4LM GPEC2A – foxFlash is now able to perform the Continental GPEC2 GPEC3 GPEC4LM GPEC2A foxFlash is now able to perform the following operations: Boot Read Boot Write On the following ECU reference: Continental GPEC2 GPEC3 GPEC4LM GPEC2A Chrysler 200 Continental GPEC3 BOOT Chrysler 200 Continental GPEC3 BOOT Chrysler 300 mk2 Continental GPEC2A BOOT Chrysler 300 mk2 Continental GPEC2A BOOT Chrysler Aspen Continental GPEC2A BOOT Chrysler Grand VojagerContinental GPEC2A BOOT Chrysler Town & CountryContinental GPEC2A BOOT Dodge Avenger Continental GPEC2A BOOT Dodge Avenger Continental GPEC2A BOOT Dodge ChallengerContinental GPEC2A BOOT Dodge ChallengerContinental GPEC2A BOOT Dodge Charger Continental GPEC2A BOOT Dodge Charger Continental GPEC2A BOOT Dodge Dart Continental GPEC3 BOOT Dodge Durango Continental GPEC2A BOOT Fiat

 OBD on the bench reading the MEDC17.9 with foxflash programmer + godiag gt100 breakout box. I want to try and write the modified files via OBD after an OBD read. The ECU data that had been corrupted is now all OK. Updated: I have had an interesting case with this ECU MEDC17.9 that had failed and had the OTP block. I read the Full flash via OBD, had the flash modified to delete CAT/AdBlue/DPF and EGR (use a tuning file service). When I got the modified file back, I decided to write it via Bench mode. I did the checksum correction using the original flash and flashed it via Bench mode 100% without any problems. The car is now starting and has no faults whatsoever and drives very well. We had brought it on a flatbed. Another great success with FoxFlash and a bit of experimenting. Read via obd on bench Write on bench MEDC17.9 bench pinout to fox flash To read and write use the following driver: → BENCH TRICORE → JAGUAR → TC1793 — JAGUAR → MEDC17.9 Attention: Some MEDC

  Problem : I had issues with FoxFlash software clicking midway through reading and kicking you off. It did it a few times on the last ECU I read but just thought it may be a connection issue & managed to read ok. It's doing exactly the same thing again. I've tried 3 different Power Supplies. Also tried to Fox & Benchbox. Tried different USB cables. The voltage suddenly drops then it fails. This is after trying various power supplied & also directly to a car battery with a charger on. I've check, recheck & checked again. Just read a VW EDC17 bench perfectly using same power supply. Any solution? Solution: Don't waste you time this ecu impossible to read on bench! Only jtag/open mode! BOSCH EDC17 CP16 [ TC1796 INT.F.] — Honda Read and write ECU in boot mode Connect with the multifunction cable the following pinout and the boot shown below. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1796 Feedback: I've mana

 After getting multiple failures on the bench due to the very tiny CAN-H and CAN-L pins on the Mazda CX-5 Denso SH13 ECU, I opted for OBD (on the bench) using the Godiag GT100 breakout box and I've managed to read the full flash with foxflash programmer , though it is much slower than on the bench. 28 minutes to read the full flash. That is a lot faster than kess v2 . the OBD pinout is the same as in the manual. You can also make a PIN adapter for the tiny CAN pins for the Mazda CX-5 Denso ECU.

 Will foxflash programmer read and write VAG Delphi DCM6.2 ECU via OBD? my kt200 doesn't work. Yes, fox flash read and write DCM6.2 via OBD without issue. This ECU needs high voltage. At least 13.5v on car System! Only in car with immo! For example: VW Transporter T6 2.0tdi Delphi dcm6.2 read, ID, VR read, Write, checksum by tool. Adblue off, all by fox flash via OBD. You also have bench option to read Delphi DCM6.2. Here is the bench pinout to fox flash .

  Problem: Foxflash reads Renault SID310 ok but Impossible to write sid 310 via OBD (Error SK2, Error Silentkey). Any solution? Solution: Start the engine and let it idle for 10 minutes, then it will allow you to write. If you turned it on, try to leave it for 10 minutes ONLY with the ignition on. The ignition MUST be left on or the engine turned on AFTER the reading for the ECU/TCU to exit the initial programming state (copying in this case). The contact must be kept at all times, at Renault "with button" it is a little more complicated because it keeps closing, there are 2 options, you press the button from 15 in 15 sec or you press the start button 20 s and then it should not close. Pcmtuner is ultra simple for sid310. http://www.pcmtuner.org/pcmtuner-read-write-renault-clio-4-sid310-ecu/