PCMtuner-tool

  Problem: Audi TT 3.2 2007 unit ME7.1.1. I can see the option in foxflash car obd but it doesn't work because it asks for a key. and bench does not offer this unit. the solution? Solution: Try another tool. Mpps can sometimes connect in Bench, on these me7.1. Or use ktag or kess3 . Ktag clone even sorts these. You will be able to read ME7.1.1 ECU fitted in Audi with a VAG part number 8E909559 / BOSCH 0261207511 using ktag in boot mode. www.iecutool.com

  Foxflash rolls out March promotion. New buyers will get 15 days of unlimited tuning support. Valid: March 1st- March 31st, 2024. Users will get unlimited tuning support for 15 days from activation. Files have no limitation among these: How to get tuning file? Provide car brand, mode, ECU type, year, original file, and function you desire to modify to www.iecutool.com . We will send your modified file in 1–3 days.

  Problem: Problem with Continental sid310, foxflash reading ok but writing doesn't let me write via OBD. voltage I attached a battery charger it was on 14v but nothing… Then I have the kess3 open the switchboard but even with the kess nothing, regarding all connections but nothing. Possible solutions: Put the ecu back in the vehicle and keep it running for 5 minutes, read password, unplug and try again… make sure your car battery is charged as power. If still failed, reading pinout password and reading and writing boot Mode boot Read pass word ok Read and write checksum ok. www.iecutool.com

  Problem: I'm new to the job, today I read a BMW EDC17CP02 ECU with foxflash tool , catch Obd, and when I wanted to write the tab with dpf off at 100%, I had an error. Any solution? Solution: EDC17CP02 has some various hardware with different types of tuning protection, that's why some work obd and some not. So just to be sure, never have to guess and look — just bench them all for piece of mind. It's a 5 minutes job to take the ecu out to bench it and get a full backup! do it and you can be super safe! If foxflash failed to read BMW EDC17CP02 on bench, check possible solution here http://www.pcmtuner.org/foxflash-failed-to-read-bmw-edc17cp02-solution/

  Problem: Got his error when trying to read this Alfa Romeo Giulietta with foxflash tool in OBD. Solution: You have to watch carefully that ecu mounts yours, because there are 1.6 105 with edc16c39 and 1.6 105 with EDC17. If it is an EDC17 ECU and you bench it. If it is an EDC16C39, check the voltage. Little low voltage. Need 13V minimum. Also C39 not always work obd. Better bench it. www.iecutool.com

  Foxflash reads and writes Audi ECU Siemens/continental PPD1.2 via OBD or Bench? Many tool will do this ECU. Foxflash works fine both OBD and bench mode. OBD Mode: OK For example: Audi A4 B7 2.0tdi 125kw ECU Siemens/continental PPD1.2 OBD read ok OBD write ok Checksum by foxflash Bench mode: We also tested the PPD1.2 on the Audi car on Bench, read, write ok, checksum by fox.

  Foxflash new feedback: Peugeot Partner K9 2020 Md1cs003 DPF off scr off Bench Read ok Write ok Checksum by foxflash www.iecutool.com

  Foxflash new feedback: Mercedes e2/3 Temic Ecu Read pin out full system (use the driver procedure and 4/5 with switch on ignition on/off) 12v bed (24v required tho) flash and e2p read

 Here is the solution to Foxflash Mercedes Benz CRD2 or DCM3.5 ECU read ok but failed to write problem. For example: Ecu Delphi CRD2.30 OM651 Mercedes Sprinter 95KW 906 Ecu read obd file is done ok Ecu write errors, Write gets to 0 percent now it's a non starter Solution: Kess v2/ kess3 for write, foxflash bricked to write. You must write in recovery option with kess the file of read foxflash. Write original file back with kess in recovery mode. You can also use flex do recovery then start then kess read/write no problem. We recommend bench on this ecu. Obd protocols i skip if possible. Feedback: Recovery by clone kess and read and write van now started. www.iecutool.com

  Foxflash new feedback: Renault midlum 280 Trw ems2.2 (truck) Read obd ok Write obd ok Checksum by foxflash. Read 8 min Write 2 steps: 1 for 17 minutes (with 2 interruptions of 120 seconds) 1 for 7.45 minutes Obd only 64kb file. src off ok.

 How to read Peugeot 208 1.2 ecu valeo v56.12 calculator with Foxflash ? Foxflash has no protocol for this ECU. It cannot read V56.12. Need Alientech KESS3 or Autotuner. KESS3 will read and write Valeo V56.12 in boot mode. Supported models:

  Foxflash reads Renault EDC17C42 ECU ok, but failed to write. It is write protected, error "OTP sector not writable"， what else can I do? Foxflash can read and write EDC17C42 fine. Not protected. Your file is bad. Bad file try to write original file and see if all is ok you have bad file. Do checksum manually.

  Foxflash new feedback: Sid307 sak tc1767 in Mercedes Benz A180 1.5TDCI @ STAGE 1 Read Password on bench. Read/Write/checksum correction in boot mode. No pass via obd, only in boot connection. MB SID307 boot pinout to foxflash Connect with the multifunction cable the following pinout and the boot shown below. Use the driver: → TOOLS BOOT MODE → INFINEON TRICORE Boot → SAK TC1767

  Foxflash new feedback: sometimes it doesn't even work on bench the Crd3 ecu's are sensitive so to save time the boot is there for security. Mercedes cla shooting break Cdi 200 Ecu Crd3E1 Boot mode ok Read/write ok Checksum by foxflash

  Foxflash new feedback: VW GOLF VI SIMOS PCR2.1 OBD OK READ OK EGR OFF OK WRITE OK Checksum by foxflash. I have disconnected and connected the battery to make flash unlock. i make obd perfectly. Car starts. www.iecutool.com

  Foxflash new user feedback: Audi a4 2020 ECU Md1cp004 Read on bench 6min Write on bench 2 min Checksum by Foxflash. All ok Foxflash pinout to Audi MD1CP004 To read and write use the following driver: → BENCH MODE → AUDI / VW → SPC5777 / TC298 — VAG → MD1CP004 www.iecutool.com

 Is it possible to read & write Mitsubishi Center Fuso ECU with pcmtuner ? Yes, with module 64 (EDC17C4–6/EDC16C31) via OBD. For example: PcmTuner OBD2 read/write Mitsubishi Fuso Canter EDC16C31 2008 4.9 engine successfully. www.iecutool.com

  Foxflash read and write Mercedes Benz Sprinter EDC15C6 via OTB mode successfully. OTB adapter is a great help. Mercedes Sprinter with a round OBD plug that requires an adapter. Simple and easy with the help of OTB. Check EDC15 C6 bench pinout Select Car OBD, Mercedes Sprinter CDI E3 EDC15C6 protocol Read ok Write ok Checksum manually with Winols. www.iecutool.com