PCMtuner-tool

 Many tools can read Opel EDC16C39 ECU over OBD, including Foxflash . Foxflash also read it on bench. On bench you read eeprom and you can see the immo code in hex format or get code from 3rd party decoder. It's not a bad solution, just takes more time. For example: Opel Zafira B edc16c39 eeprom bench reading, to extracting pin code for key learning. Foxflash Opel EDC16C39 5

  Foxflash new user report: Backup DCM6.2a PSA in boot successfully before injection test in obd. new calculator, never done, so a backup to have peace of mind. FYI: We have done many in OBD with foxflash DCM6.2a and DCM6.2c its safe to do , Just exit eco mode in the bsi with you diag tool (i.e Autel MK906 pro/diagbox) before read/Write so ECU doesnt go to sleep + put a voltage stabilizer or cables when you Write. So Dcm6.2A is fully safe in OBD. www.iecutool.com

  Problem: It is a Med17.1.1 Audi RS5 bench not ok with foxflash . 8T1907560E Hw 005. Tprot update, Password boot ok, read no ok. Foxflash saves file password but impossible to Read/Write this ecu. in boot mode password vag tprot8 ok, after reading it says not have the password. Even ktag & pcmflash dont read him. Possible reason & solution: MED17 vag not clonable with foxflash/kt200 etc. otp zone not clonable you need a good tool that allows you to copy the PIN / MAC / CS / VIN, either you turn off taura a safe default on the counter however given that the pins and all will not respond, or you adapt with odis online. see also: http://www.pcmtuner.org/foxflash-vag-med17-1-otp-sector-not-writeble/

 One of our customers reported that he got 'unable to connect to remote server' after installing foxflash software on Windows 10 system (image attached). Ieutool.com engineer check the issue via Teamviewer and found it was the system issue. Need to install foxflash software on a clean Windows 10 system. NET framework version is too low. Need to install NET framework 4.8 in order to run foxflash manager.

  Problem: I got the foxflash software and manager well installed, but get this error after installation. Error "An internal exception occurred". Any idea? Solution: If someone get this error after installation, please reintstall your windows to windows 10 without updates, then install visual ++ 2015, then it will work. www.iecutool.com

  Foxflash new user feedback: Adblue off on a Citroen c3 Aircross 2022 MD1CS003 ECU is not locked. -read ID ok -read on bench with foxflash -Checksum correction with foxflash -Write on bench with foxflash

  Foxflash new user feedback: BMW F10 Continental MSD87. 1 TC1796 PASSWORD SEARCH successfully Using the OTB adapter Protocol: Tool Boot mode->Infineon Tricore Tool Password->OBD Password MSD80/81/85/87 BMW OTB pinout is in the foxflash document.

  Foxflash new user feedback: Mini One 1.6 Gasoline Just get ECU Siemens EMS5150 not car Read ok with OTB 1.0 adapter Write ok with OTB 1.0 adapter E85 Checksum by WinOls All perfect. OBD on bench pinout is on the document.

  Foxflash failed to read Jeep 2021 EDC17C69 TC1793 ECU on bench. Error SK2 Bench locked. 2021 have tprot. Not possible read by aftermarket tools. Foxflash cannot read it as bench locked. Bench mode uses a security exploit in Firmware to gain access to bootloader on processor, after 2020 most manufacturers update ECU firmware so exploit no longer works.

  Problem: Foxflash reads Jaguar ECU Edc17cp11 with no problem, when write ECU it gave an error. Any idea? Solution: It says on the program, use higher voltage. 13volts minimum. That stock power dc not enough. Recommend buying lab power supply. www.iecutool.com

  Foxflash new feedback: Fiat marelli MJD 8F2 ECU. Read ID ok read bench ok write bench ok Checksum done by the mapper but Fox I'm doing it without worries I've done it several times.

  Foxflash new feedback: Peugeot DCM3.5 read and write ok. To read and write use the following driver DELPHI DCM3.5 — MPC5566 — Peugeot, Citroen, Ford pinout Solder the rainbow flat cable on the pcb: Solder the rainbow flat cable on the pcb: This is the way how the customer did it. www.iecutool.com

  Foxflash new feedback: Renault Trafic 2.0 dci 2012 EDC16C36 561/2 on Bench 13.5 Volts Terminal clamp 7 on the bench box read ok Write ok Stage 1 Foxflash pinout to EDC16C36

  Foxflash new feedback: Sid310 Nissan Read and write via obd. It is a 2017 nissan navarra 2.3. Write by OBD, takes 10 minutes. Checksum ok with foxflash. For Nissan/Renault SID310, better boot on it, it's better to open it. Read also: http://www.pcmtuner.org/foxflash-continental-sid310-obd-write-error-sk2/

  Foxflash new feedback: Mercedes crd3p.D1 ECU Foxflash bench pinout to Mercedes CRD3P.D1 To read and write use the following driver: → BENCH MODE → MERCEDES BENZ → TC1793 — MERCEDES and choose: → CRD3P.D1 Read ok Write ok Checksum by foxflash Adblue off ok www.iecutool.com